Im Buch
Ergebnisse 1-3 von 5
Seite 431
摘要 9 本研究首先在檢測 ADO - SiO 漿料之流動性及成形速率。漿料是以 Also : SiO2 為 9 : 1 之重量比,加水,球磨配成固含量( SC )為 50,60 及 70 %之三種漿液,並以 NaOH 及 HCI 溶液調成不同 pH 值,而以黏度計在不同轉速下,量測其流動性。
摘要 9 本研究首先在檢測 ADO - SiO 漿料之流動性及成形速率。漿料是以 Also : SiO2 為 9 : 1 之重量比,加水,球磨配成固含量( SC )為 50,60 及 70 %之三種漿液,並以 NaOH 及 HCI 溶液調成不同 pH 值,而以黏度計在不同轉速下,量測其流動性。
Seite 435
(二)越流性與卻流性一般泥漿的流變性主要有二種,一為盘流性(泥漿一旦停止攪動,就會變得更稠黏,若再攪動又恢復流動性) ,二為卻流性(泥漿攪動時,不易流動,而靜置時則較易流動) ,從圖(三)中可看出 Also - SiO 漿體為盘流性之繁體,且黏度愈大,其热流性愈顯著, ...
(二)越流性與卻流性一般泥漿的流變性主要有二種,一為盘流性(泥漿一旦停止攪動,就會變得更稠黏,若再攪動又恢復流動性) ,二為卻流性(泥漿攪動時,不易流動,而靜置時則較易流動) ,從圖(三)中可看出 Also - SiO 漿體為盘流性之繁體,且黏度愈大,其热流性愈顯著, ...
Seite 438
AlO3 - SiO 嫌體於此值為 10 ~ 12 時,黏度最低,流動性較佳。 2.提高漿體的固含量可加快成形速率,縮短成形所需的時間。 3.提高固含量及降低黏度可同時降低煅燒體的孔隙度,並提高其密度值。 4.在本實驗之條件下所得之鑄件為一類多孔型陶屬元件。
AlO3 - SiO 嫌體於此值為 10 ~ 12 時,黏度最低,流動性較佳。 2.提高漿體的固含量可加快成形速率,縮短成形所需的時間。 3.提高固含量及降低黏度可同時降低煅燒體的孔隙度,並提高其密度值。 4.在本實驗之條件下所得之鑄件為一類多孔型陶屬元件。
Was andere dazu sagen - Rezension schreiben
Es wurden keine Rezensionen gefunden.
Andere Ausgaben - Alle anzeigen
Häufige Begriffe und Wortgruppen
academic Accounting activities Admission to Higher Analysis applicants appraisal assume base better blocking Business C-test carbon fibers changes channel coefficient College Entrance Examination colleges and universities Committee continuous Decision decrease defectives density Department Design Development distribution effect equation error estimator expected failure costs Figure function given groups Herbert higher education Improvement increase indicates institutions International Joint Journal language Management materials means measured message channel method Ministry of Education obtained organization passage periodic Planning poem polymers practice prevention probability problem procedure properties quality costs random walk ratio reliability Report request Research respectively response sample schools scores selection shown shows shrinkage stabilization structure Study Subcommittee subjects suggestions Table Taiwan temperature transmissibility unit University values